A dry ice sand blaster is a cleaning system that uses compressed air to shoot dry ice pellets onto a dirty surface. The cold (-78°C) makes contaminants brittle, then the dry ice turns into gas and expands 800 times, lifting away the dirt. No water, no sand, no chemicals. This equipment is typically used for mold cleaning, automotive carbon removal, electronic component deflashing, and petrochemical maintenance. Don’t damage your surfaces. If you need reliable equipment for your next project, contact YG Machinery for a custom quote.
Specifications for YG Portable Dry Ice Blaster
| Model | YGP7X | YGP6 |
| Motor power | ＜500W | ＜500W |
| Voltage | AC220V, 50-60HZ | AC220V/50-60HZ |
| Air consumption | 28-106 CFM (0.8-3.0m³/min) adjustable | 28-106 CFM (0.8-3.0m3/min) adjustable |
| Air supply pressure | 0.1-0.9Mpa (1-9bar adjustable) | 0.1-0.9Mpa (1-9bar adjustable) |
| Ice delivery speed | 0-0.75kg/min(adjustable) | 0-1.65 lbs/min (0-0.75 kg/min) adjustable |
| Hopper capacity | 10.5kg (23.5 lbs) | 23.5 lbs(10.5kg) |
| Degree of protection | IP54 | IP54 |
| Machine weight | 121 lbs(55kg) | 110 lbs(50kg) |
| Dry ice state | 2.5-3mm (granular) | 2.5-3mm(granular) |
| Drive mode | Direct connection | Direct connection |
| Machine size(L x W x H) | 510x460x960mm | 600x400x860mm |
How the Portable Dry Ice Blasting Machine Works?
A dry ice sand blaster uses granular dry ice (2.5-3mm). The operator pours dry ice into the hopper. Compressed air enters the machine at 1-9 bar. An adjustable feeder sends dry ice into the air stream. The mixture travels through a hose and exits a nozzle. When the pellets hit the surface, they create a thermal shock. The contaminant cracks and shrinks. At the same time, the dry ice sublimates from solid to gas. The rapid expansion (800 times) blows the dirt away. The only thing left is the dirt that was removed. No secondary waste.
Key Advantages of Portable Dry Ice Cleaning Machine
1. No water, no chemicals, no sand
A portable dry ice blasting machine cleans without water runoff, solvent fumes, or abrasive dust. You can use it on electrical panels, motors, and sensitive electronics because dry ice is non‑conductive and leaves no residue. No secondary waste means no cleanup after cleaning.
2. Gentle on surfaces
Dry ice pellets are soft. They disappear on impact. This means they will not wear down mold cavities, strip coatings from aerospace parts, or scratch polished surfaces. The dry ice sand blaster cleans without changing the part’s dimensions.
3. High efficiency
One person with a portable dry ice blaster can clean a rubber mold in 15 minutes. The same job used to take two hours with hand scraping or chemical soaking. The machine works in line, so you do not need to disassemble the equipment.
4. No disassembly required
Because the dry ice sublimates and leaves no mess, you can clean machinery in place. Open a cabinet, point the nozzle, and spray. Production downtime drops from hours to minutes. No gaskets or seals to replace afterward.
5. Environmentally friendly
The only byproduct is the contaminant you remove. Dry ice is recycled from other industrial processes. It does not add CO2 to the atmosphere. No hazardous waste disposal needed. No paperwork for solvent handling or wastewater permits.
6. Portable and easy to use
A portable dry ice blasting machine weighs 50-55 kg. It has wheels and runs on 220V power. A new operator learns to use it in about 30 minutes. Adjust the air pressure and ice feed, then pull the trigger.
Where to Use Dry Ice Sand Blaster?
- Rubber and plastic molds: Remove release agents, carbonized residue, and uncured rubber. Vents and cavities are cleaned without removing the mold from the press. The machine reaches deep into blind holes and narrow slots.
- Automotive: Cleans intake valves, piston crowns, EGR systems, and engine bays. No engine disassembly needed. The dry ice blaster strips carbon buildup that causes a rough idle and loss of power.
- Electronics and PCB: Removes flux, solder paste, conformal coating, and dust from circuit boards and robotics. Non-conductive and leaves no moisture, so sensitive components stay safe. No drying time required.
- Printing: Cleans dried ink from gears, guides, and nozzles. Works on both water-based and solvent-based inks. The machine eliminates the need for toxic solvents and lengthy soak times.
- Food processing: Removes baked-on grease, flour, and sugar from ovens, conveyor belts, and mixers. No chemicals, so no rinse cycle. Production can restart immediately without waiting for drying or chemical clearance.
- Petrochemical: Cleans heat exchangers, compressors, turbines, and boiler tubes. Removes coke, scale, and hydrocarbon sludge without abrasive media. No secondary waste means lower disposal costs and less downtime.
Get Your Dry Ice Cleaner Price from YG Machinery
YG Machinery is a manufacturer that supplies dry ice sand blaster equipment to the United States, Europe, Southeast Asia, and the Middle East. We accept custom orders for special nozzles, longer hoses, and different voltages. If you need a reliable dry ice cleaner price that balances quality, cost, and technical support, contact YG Machinery for a custom quote. Every machine is tested before shipping. We also provide spare parts and remote troubleshooting. Get your quote today.
